6 Solutions For Bosch Miter Saw Bevel Stuck

Bosch Miter Saw Bevel Stuck
Bosch Miter Saw Bevel Stuck

Bosch is a famous brand known for manufacturing power tools for its users.

The brand has several lineups that they have come up with and each of them is equipped with unique features. Keeping this in mind, people must go through the specifications for these devices carefully when purchasing them.

The miter saw is one of the best tools from the brand that comes with several useful features.

This includes the adjustment options that allow people to select how deep the cuts made should be. So, if you’re aiming for an upgrade for your current system, Bosch is for you. 

You can also alter the speed ratings of the power tool which allows for better versatility.

With that being said, there are also some problems that people can run into with these devices. So, you’ll have to go about limiting these errors to figure out a suitable solution.

When it comes to this, a common issue that you might notice is people reporting that the Bosch miter saw bevel is stuck.

If you are having the same problem, then going through this article should help you in finding some troubleshooting steps that can be used.

Bosch Miter Saw Bevel Stuck

  1. Unlocking The Pin Inside Your Tool

When setting up the Bosch miter saw, people will notice that its bevel is stuck and does not move. This can be quite annoying as it prevents users from adjusting the device as well as from lifting it.

Although, you should note that the lock is a feature from the brand that ensures that the blade does not get lifted accidentally.

The right side of the tool has a small pin and retainer that holds it in place. If you access this and then pull the pin, then it should release the system and allow you to use the device without any issues.

Simply doing so ensures that the bevel can be moved around, and you can then lock the power tool once you are done using it.

  1. Using An Electrical Tool

husky tools

If the retainer and pin are stuck, then this might mean that the connectors on your miter saw might be clogged. People can try pulling the pin with excess force, but they must do this carefully as it can also break.

If the bevel is still stuck, then you might have to use an electrical tool to loosen up the connection for your device.

Both air guns and impact drivers are great options as these can be used in reverse to unlock the tool. Just make sure that you do not use too much force as this can break the ring in your miter saw.

  1. Clean Commutator

Cleaning the commutator should be your next step when you can’t seem to secure any response from the system.

These issues are surely annoying, but can be more complicated when you’re not keeping track of the maintenance. 

There is a good chance that the commutator is dirty and the system is clogged up.

clean

The only thing that you can do here is to rely on sandpaper to clean up the commutator. It will take a bit of time, but you can get a decent response after you’re done cleaning.

Just make sure to remove all power from the unit before you start the cleaning routine.

After that, you can fold up the sandpaper and slide that in to clean up the gunk. It will be that hard and you will be able to rely on minimal pressure.

From there, you can also blast the unit with compressed air. This will get rid of the lodged debris and the free gunk.

After that, you can wipe away the residue one more time and that will be enough to have you sorted out right here. 

You can also hire an expert to help you here. Reaching out to the local contractors is never a bad idea and you will not have to spend much cash to get help from the experts.

All that you have to do is to explain your end, and the dealer will be more than happy to guide you. 

  1. Use WD-40

WD-40

The next thing that you need to do here is to rely on some WD-40. Spraying some WD-40 on the pivot points is not a bad idea either when you’re using the system after a long time.

This method is pretty easy, and you will not have to spend much time trying to get through the issue. 

All that you have to do is to spray the pivot points and completely cover the commutator.

From there, you can leave the residue to rest for about 20 to 40 minutes. Next, you can apply one more coat of the WD-40, and leave the unit for an hour. 

At this point, you can try using the bevel and it should move. You will still have to go through the cleaning routine but the rust will be more loose and you will not have to worry about the gunk or the buildup.

Hopefully, these pointers will be enough to guide you through the error, and you will not have to struggle with as many errors.

All that you have to do is to keep track of these issues, and you will be sorted out in no time. 

  1. Check Tension On The Locking Nut

Checking up on the tension can be another crucial thing that can help you avoid this error.

error

If you’re not that sure about the locking mechanism and believe it to be disengaged, then loosening up the tension is not that bad of an idea. 

You can just rotate the bolt to loosen it up a bit and then check the response from the bevel. In most situations, the response should be better and there should be a bit of slack. This slack will help you get rid of the lodged gunk.

From there, you can go about cleaning the pivot points and using the materials listed above to sort out the situation.

Yes, it will be a bit of hassle for you to go through all of these steps, but if you take care of the maintenance from this point, you will not have to worry about the same issue. 

After going through with these fixes, you will be able to get an amazing response from the unit. You will not have to brother with the same errors again, and fixing the unit will be pretty simple. 

However, if you’re not that lucky, and the issue still persists, then you should reach out to the dealer. You might just be dealing with a defective system, and the dealer will be able to guide you on these errors.

  1. Contact Customer Support

support team

Finally, if you are still running into the same issue then contacting the support team for Bosch is your only option.

This is because there might be a chance that some part of your miter saw has gotten damaged. This is quite rare, and the problem can usually be fixed using the steps mentioned above.

However, if you are contacting Bosch then make sure that you provide them with all the details about your issue.

They will then provide you with a solution or ask you to bring in your miter saw for repairs.

They might even point you towards the nearest repair center and you will be able to get the unit fixed for free.

This is only true for the owners that have a valid warranty. So, if you’re also working with a warranty, just rewatch out to the dealer.

dealer

He will be more than happy to point you in the right direction, and you will not have to deal with as many complications. So, be sure to reach out when you can’t fix the issue yourself. 

Wrapping up

Bosch is a great brand, but that doesn’t mean that you will always have an amazing time with these tools.

There are some complications that you can expect with this system, and owners often list issues with the hardware. Most of these issues are caused by ignored maintenance.

This is especially true for situations with the Bosch Miter Saw Bevel stuck.

If you run into this issue, then we suggest that you go through the fixes listed above. You will have to go through a bit of hassle to go through all of these pointers. 

However, you’re not left with many options when the bevel is stuck on the Bosch miter saw.

All that you can do is to reach out to the dealer and have him guide you through a fix. You will not have to worry about this hassle on your own, and you can just have the expert guide you through a fix.

There is simply no gain in trying to fix the bevel on your own if you’re unsuccessful after going through the solutions above.

Instead, you need to let the dealer take change, and you can also claim the warranty. That way, you will not have to worry about the purchase security. 

Leave a Comment