Ryobi 40V Chainsaw Stopped Working? Try These 7 Handy Fixes

Ryobi equipment is matchless when it comes to efficiency, durability, and power at the same time, and you get to enjoy the right perfection on all accords with it at the same time.

So, if you’re not that sure about which unit to start out with, Ryobi might present a decent portfolio.

They are also manufacturing some of the most powerful chainsaws with portability options since they are cordless and powered by a battery.

This brand has been dominating the market for years, and some models even outperform premium options like DeWalt and Milwaukee.

However, just like every other power tool available on the market, you will have to make sure to follow through with the maintenance and cleaning of the Ryobi system as well.

Ignoring the maintenance will only set you up for failure, as you will struggle to get a response out of the machine.

Ryobi 40V chainsaw is one such chainsaw that is ergonomic, lightweight, and has the right power that you will need to make it work. If the chainsaw stops working out of nowhere, here are a few things that you will need to fix.

Ryobi 40V Chainsaw Stopped Working

1. Charge the Battery

Naturally, the first thing that you will need to take care of is charging the battery since the battery might be getting low on charge, and that will stop the chainsaw from working as well. 

So, you just need to disassemble the battery and then charge it up to ensure that you are able to make the Ryobi 40V chainsaw work once again.

Yet, charging is not the only thing that you will need to be careful about, you also need to ensure that you are checking on the battery being installed properly as well and also the optimal battery health since battery health deteriorates as well, and that might be the problem with your chainsaw to stop working.

2. Check the Fuses

There are also some fuses on the Ryobi chainsaw that you will need to be careful about since they can be blown as well due to a number of reasons, and that will cause your chainsaw to stop working out of nowhere.

So, all you need to do is get the cover off and check all the fuses that are there on the chainsaw.

If you find any of these fuses to be blown, you will need to replace that with the exact same fuse, and that should be enough for you to make it all work for you.

After you get that sorted out, you will not have to face any further problems, and it should be working optimally, getting you the right experience, you might have been seeking earlier.

3. Clear the Chain

Also, the problem can be with something or some bigger particle getting stuck on the chain of your chainsaw, and that would stop your chainsaw from working optimally as you would normally want it to.

That problem is also something that is common, and you will be facing this pretty often.

So, you need to ensure that you are turning off the chainsaw and then cleaning the chain optimally. 

If you find any such object stuck on the chain, you will need to take it off for sure and also keep the chain lubricated moderately to ensure that you don’t have to face any such problem with the chain getting stuck or causing too much friction with the motor.

An effective and regular cleanliness routine should optimally help you out, and you will not have to face any such problems afterward either.

4. Loosen Up The Chain

Sometimes, all that you need to do is to loosen up the chain a bit to get it to engage properly.

There is no debate that having too much strain on the system will hold you back in the long run. You can avoid that situation pretty easily by creating a bit of slack in the system.

All that you need to do to fix the issue is to loosen up the adjustment nut by a little margin and make sure that the saw cover is on.

This will prevent the saw from coming off, and the blades will be engaged through and through. So, you will not have to deal with any errors in the long run.

However, you’ll have to go through a bit of trial and error to find the perfect balance.

Having too much slack in the system can also be problematic as well. So, be sure to test out a few different configurations to find the right spot for your projects. 

5. Check the Temperature

If the chainsaw stops in the middle of normal operations, then the issue might be more related to the chainsaw overheating.

Depending upon the type of material you’re using, along with the model of the chainsaw, it is likely that you’re putting too much strain on the system.

This is never good, and you need to slow down your approach when it comes to fixing the unit.

Trying to take a few minutes off to let the chainsaw cool down will not only help with the unit’s performance, but you will get a more precise setup.

So, be sure to check up on the temperature and allow the device to cool down a bit if it is too hot. That might be it when you’re dealing with the majority of hardware issues with the system itself. 

6. Check For Hardware Damage

Next, the probability of hardware issues increases by a huge margin. This issue is more common for users that have been using the system for years.

So, if you’re in the same boat and not storing the unit properly, then you will have to check up on the hardware as well.

Even the best units will not last more than a few years if you keep them out in the open and exposed to moisture and humidity.

This will only develop gunk on the pivot points, and the connections will get corroded over time.

So, all that you need to do here is to check the unit for hardware issues and clean them accordingly.

It will take a few minutes at max if the situation is not that bad. You can also reach out to local experts if you’re not sure about how to keep the device maintained. 

Similarly, if you got a damaged unit out of the box, then you need to reach out to the dealer immediately.

There is no point in trying to fix a defective unit yourself, and the warranty will cover all damages. So, you will need to get a fresh piece to avoid more issues down the road.

7. Call The Official Team

Lastly, you can also get help from the official support team. There is no point in struggling with all of these steps when you can get help from a complete panel of professionals maintained by the Ryobi help center.

These experts will not only help you figure out the issue but will also guide you through each step of the troubleshooting process.

All that you need to do is to list the possible errors with the device and the troubleshooting methods you’ve tried so far.

It will speed up the isolation process, and these experts will be able to quickly grasp the situation.

From there, you just have to follow through with the pointers listed by these experts. Hopefully, you’ll be able to fix the unit right here. 

On the other hand, if you’re not that lucky and the system seems to be in poor shape, then you can demand a replacement here.

Depending upon the warranty status and the validity of the claim, you will be able to quickly secure a new piece from these experts.

So, be sure to reach out and get help when you can’t seem to get ahead of these errors yourself. 

Wrapping Up

Can’t seem to get your Ryobi 40V to work properly? Just test out some of the troubleshooting methods mentioned here.

Nine times out of ten, you will have an effortless experience with this device. So, be sure to follow through with the instructions given above to get the desired response.

Most of the time, you will just have to check up on the battery and the power supply to the unit itself.

It will be enough to fix the majority of errors, and you will not have to deal with more errors down the road, and the device will start working perfectly.

From there, you can proceed with cleaning the chain and checking for hardware issues.

If the unit seems to be damaged, then the situation can become a bit stickier. You will have to check on the system for damaged components or frayed sections. 

There are no quick methods that play into fixing a damaged unit, and reaching out to the dealer will help you get a better hang of the situation.

As long as you have a valid warranty to work with, fixing the unit shouldn’t be that hard of a problem when you’re dealing with Ryobi.