Most people already know how amazing the power tools manufactured by Bauer are. While the brand previously used to focus on devices that had a powerful motor on them, you will notice that Bauer now works on providing its users with cordless tools.
These are not only compact, but the devices are also capable of delivering large amounts of power. The lithium-ion battery on them can last about 24 hours if completely charged, which is a long time.
Though, you should note that these batteries can only be charged as long as you have a charger that supports their voltage.
Talking about this, Bauer usually provides its users with a compatible charger if they purchase the entire power tool kit from them. While this can be amazing, you will notice that there are also some issues that the device can run into.
Recently people have been complaining that the battery charger from Bauer is blinking red and green. If you are getting the same issues, then here are some simple steps that can be used to fix them.
How to Solve Bauer Battery Charger Blinking Red And Green?
- Force Mode Activated
One of the main reasons why your Bauer charger might be linking red and green can be that you are using force mode.
This can be enabled by sliding the charge mode button provided on your device. Once done, the charger will start to blink lights indicating that the feature is switched on, and it will then try to charge batteries even if they are not supported.
The service is added to charge batteries that have a power rating listed under 2V. Considering this, if you are using a battery that supports the voltage rating on your charger, then the feature should be disabled.
This can sometimes overcharge or undercharge the battery, resulting in it getting damaged. The feature can be disabled by sliding the mode button present on your charger.
- Overheating Charger
Previous models of the Bauer charger did not have the force mode feature mentioned above.
Hence, if you have an older model, then the green and red-light blinking might indicate that your charger is overheating. You can confirm this by placing your hand on the device and feeling its temperature.
If you notice that it has started getting warmer, then remove the charger as well as the battery from your power tool and leave all of these to cool off.
The charger should be safe to use within 30 minutes, but sometimes an even longer time might be required.
- Battery Connections
Sometimes when people try charging the batteries right after using the power tools, some debris might enter the connections.
This can prevent the charger from establishing the connection required with the battery, resulting in the green and red lights blinking.
The problem can be easily fixed by removing the battery and then cleaning off the ports for both the charger as well as the battery. If done properly, then your problems should be gone.
However, if you are still getting the same error, then there is a high chance that your batteries have gone bad. The only fix, in this case, is to replace these with new ones.
- Check Power Supply
At this point, you need to check the power supply for errors. There is no point in trying to check the charger for issues when your electrical connections are in rough shape. No charger will work with a damaged outlet, and you can narrow down these errors by trying a different one.
It can take a few moments to check the output with the help of a multimeter. This is especially true if you’re a bit experienced and know how to handle the maniac of your electrical connections.
On the other hand, if you don’t know a thing about how to use a multimeter, then your best bet is to rely on professional support. You won’t be able to do anything about the system yourself.
So, reach out to some local experts, and they will help you fix the connection points.
Ideally, you should hire a professional every six months for the maintenance of your home. Otherwise, you will notice a rapid decline in the performance of your appliances. So, keep that in mind if you can’t seem to secure any response from the charger.
There is no point in going cheap and using a different outlet. You should immediately have all the electrical connections checked, and you can get ahead of this blinking error in no time.
- Inspect Unit For Hardware Issues
There is also a chance that you’re in possession of a defective unit. The delivery process can be especially hard on electronics. So, there is no harm in inspecting the unit. You might be able to find some cracks and damaged sections.
If that is the case, you need to claim the warranty immediately. You’re not liable for any damage to the device. So, if you keep running into these errors, just inspect the unit one more time.
All your focus should be on isolating the errors with the hardware.
Similarly, if you happen to get a bit of water or any other solution on the unit, then that can also create these blinking errors.
So, if you’re in this situation with the charger, just leave it out to dry. However, it would also help if you could wipe away the hunk from the unit.
It never hurts to keep your devices clean. So, manage the system accordingly, and you won’t have to worry about anything.
- The Battery Might Be At Fault
Ideally, all the issues with the charger will be fixed at this stage. However, if you’re not that lucky, then chances are that your battery pack is to blame here.
All you need to do is to check for damaged sections or leaking problems. If the battery is in rough shape, you will have to get a new one.
You can’t do much about any situation with the battery being defective. So, keep that in mind if you have been using the device for a long period.
Just make sure to get a compatible replacement, and that would be it when it comes to battery problems.
However, if you’re in a situation where the battery is simply drained out, then you can jump it up from a different pack.
Just get a pair of wires and connect the terminals on a drained and charged battery. Keep the wires connected for around 20 minutes.
From there, you can install the battery back into the charger, and there won’t be any errors with the blinking light. Hopefully, that will be it when you’re dealing with battery-related errors.
- Seek Help From Customer Care
Customer care is pretty decent when you’re in business with brands like Bauer. So, if you can’t seem to figure out the problem, just call the customer care team. They will be more than happy to guide you through a fix.
This is true even if the warranty has expired. So, keep that in mind and reach out to these professionals. Just provide a clear and detailed description of the issue.
That will make it much easier to narrow down these errors. From there, they will guide you thoroughly through each step of the way.
- Claim Warranty
On the other hand, if you’re sitting on a valid warranty and it has been less than a year since you bought this charger, then you can follow through with the claim. There is no point in wasting your time servicing and operating the machine.
Instead, you need to let the experts take over the job. They will help you through the error and then provide you with a replacement if the issue is genuine.
In most conditions, you won’t have to wait more than a few days to get through these errors.
Hopefully, you won’t ever have to deal with the same errors with the new unit!
changer flashing red and green all the time when battery in changer
My battery seems to last only a few minutes under load. I recharged it and the light went red and then solid green after charging for about an hour. Now, it lasted only about two minutes under load being fully charged. now, i plugged it into the charger and i get two light red and green solid blinking. No charge at all now. Must be a bad battery pack i guess? I won’t know until i can get another battery to check and see if the charger will blink red and green again on new battery. If so, bad charger i assume then.
I have two Bauer 20 v lithium 5.0AH batteries I use on a regular basis,now one of them when placed on the rapid charger ,that came with, starts out like it’s going to take a charge then rapidly red green blinking. The battery has 12.3 volts showing on vt.metr. is that enough v for the charger to recognize to start charge process?