Bosch is a German multinational engineering and technological company. The company provides mobility offering facilities for private or commercial vehicles, smart transport infrastructures, and whatnot.
It is also considered the world’s market leader for power tools and their accessories.
While some owners say that DeWalt and Milwaukee are more consistent when dealing with power dolls, that is not always true. It all comes down to what projects you’re aiming at.
So, if you’re new to the market, Bosch might not be such a bad idea.
It offers an amazing table saw too. The table saw is made of fine material and has good build-in quality. However, many people often face problems related to the Bosch 4100 table saw.
Therefore, we have listed below some common Bosch 4100 table saw problems and their ultimate solution in the given article. Hopefully, you won’t have to run into these issues if the unit is kept clean.
Fixing Bosch 4100 Table Saw Does Not Power On:
One of the common problems the users of the Bosch 4100 table saw might experience is that the tool is not switching ON. In such cases, check if the switch is turned ON. If not, simply turn the switch ON.
Also, make sure that the plug is working fine. Use a multimeter to check for continuity. If the plug is faulty, use a plug that works fine and gets the job done.
There are a ton of other reasons Bosch 4100 Table Saw problems might be at fault here, from hardware issues to device damage. So, you’ll have to go through a bit of troubleshooting to narrow down this error.
However, if you do find the hardware to be damaged after a demanding project, then you need a new unit.
There are no quick fixes that can help here, and your first move should be to call the dealer for a replacement. Ideally, you won’t have to worry too much about the warranty here.
- The Tool Acts Funny.
The problem that you might face when using a Bosch 4100 table saw is that it might act funny. This usually happens when it is kept in storage for a longer period of time.
In such cases, it might not turn on first. If the tool does turn on, then it may produce some strange noises and vibrate a lot.
For such cases, first, remove all the dust and dirt that has been built up over time in storage. It is preferred to use a vacuum first and then compressed air.
If the cleaning does not help, then try replacing the tiny circuit board that is often tucked into the top of the black plastic housing around the field coil.
The tiny circuit deals with the soft-start function of the saw. Replacement of the circuit board will help get rid of the problem.
- Motor House Behaving Rough
Another problem you might face regarding Bosch 4100 table saw is the rough behavior of the motor house. Mostly, the bearings are responsible for such behavior of the system.
Try replacing the bearings. First, find the bearing that is causing the problem. Then, remove the bearing from the tool with the help of a puller.
Replace the bearings with the ones that are compatible with your device. We do not suggest repairing the bearings because replacement is the only long-term solution to the problem.
Also, the bearings can also not be repaired in many conditions.
- Bosch 4100 Table Saw Blade Adjustment Seized
Other Bosch 4100 table saw problems also include blade adjustment problems. The blade adjustment might seize several times when you are trying to use the tool.
Normally, thorough cleaning of the tool with the help of compressed air can help fix the problem.
However, if the cleaning does not work, then try turning the tool upside down. Also, make sure that its face is resting down. This will make the tool work normally.
However, if you face a condition where the tool is working perfectly when upside down but while in the upright position, it consistently gets stuck or seized, then you should replace the gears for the blade adjustment crank.
You can get these gears from any local tool shop.
But we prefer you to use the Bosch replacement gears for the tool. Make sure that you follow proper precautions while replacing the gear of the table saw.
Any irresponsibility can cause the tool to be lubricated, which will introduce other problems to your tool.
- Blade Does Not Speed Up
Issues with the blade not coming up to speed are not that rare either. However, these are usually easy to fix. So, you don’t have to worry about going through the extensive routine, and a bit of cord adjustment will do the trick.
The most consistent fix here that helped out the majority of owners was changing the extension cord. So, if you’re stuck in the same error, be sure to find a new extension cord that is compatible with power tools.
Other than that, the voltage might also be to blame. If you’ve not serviced the electrical connections in a while and the unit is still not responding, then it is time to call an electrician. You should never try to service the connections yourself.
There are simply too many reports of owners electrocuting themselves while trying to adjust the power system. So, if you’re in the same boat, be sure to hire an expert. There is no point in wasting your time getting around this error.
Having the connections fixed will not only increase the lifespan of your appliances, but you’ll also minimize fire hazards. So, keep that in mind as you try to adjust the workshop.
Precautions
To avoid these problems, there are a few tips and tricks that might be helpful such as making sure to clean the tool properly with the help of compressed air.
This is because cleaning usually helps get rid of the majority of the problems related to the tool. Also, check the gears and motor occasionally to catch any problem related to these parts in advance.
You won’t believe what a bit of cleaning can do about your unit. So, even if you ignore the maintenance for a week, you can expect to run into some of the issues mentioned above.
Hopefully, you won’t have to try hard to get through these errors.
Lastly, you need to also check the condition of the blades. If the blades are a bit dull, and you can’t seem to narrow down the errors, then you need to get these blades replaced. You can’t really expect the unit to get up to speed when the blades are damaged or dull.
All in all, keeping the unit clean and the blades sharp will be it when you’re dealing with this saw.
From there, it is not that hard to consistently get an optimal response from the device. Hopefully, you won’t have to go through any hassle even if you do run into the issues mentioned here.
The Bottom Line
To conclude, Bosch is an amazing company providing its users with mind-blowing tools and tool accessories. The table saw offered by the company is one of their leading tools.
However, there are some problems you might face when using the tool. To know more, go through our article mentioned above.