Milwaukee is simply known to be one of the best tool manufacturers out there in the US since they manufacture some of the most durable and budget-friendly tools for one to choose from.
Everything from the dealer support to the lifespan of its devices is exceptional.
So, if you’re new to the market and can’t find the optimal unit for your project, browsing through the Milwaukee portfolio will make the job easier.
Hopefully, you’ll be able to find an option that will best suit your budget as well as the project requirements.
All that will allow you to not only choose from their wide range of inventory but also have the right tool that you might need to get any job done in the best possible way.
Milwaukee M18 Propress Not Working
M18 is one such series that you get to enjoy with 18V of power output and perfect durability.
M18 ProPress is one such tool from Milwaukee that can help you with multiple compression needs.
If you are looking to get it, here are a few things to be careful about if it is not working.
- Not Powering On
The first thing that you will need to be careful about is the tool not powering up normally as it should, and that could be real trouble for you to have.
That is why you will need to ensure that you are checking on it properly. To have this problem fixed, you need to ensure that the batteries are properly installed on the tool and they are not loose or something.
You also need to ensure that you are checking optimally on the charging.
If the batteries are not charged, not connected properly, or have some other problem on them, such as corrosion on the battery terminals, you will need to clean it up.
- Jaws not Adjusting
Another issue that you might have to come across while you are using the Milwaukee M18 Pro Press tool is that the jaws might not be adjusting properly on the tool.
That could cause you to have inconvenience and downtime for any work that you might have planned. That is why you will need to ensure that you are getting it fixed up properly on the jaws.
At times the jaws can be simply stuck due to some rust or any other particles being stuck on the spring.
So, a rust removal spray should be helping you out optimally, in this case, to help you out in order to have all such problems fixed, and you will not have to worry about a single thing.
You also need to be careful about the wear and tear on these jaws since these are metal components, and they can also get loose over time, which can cause you to have problems with getting them adjusted.
- Battery Problems
The next thing that you need to be careful about is the battery situation. You will find a ton of owners struggling to charge the battery.
Similarly, there is no deficiency of complaints from owners dealing with a defective battery pack where the battery timing is too poor.
Almost all of these issues are related more to the charger and not the battery itself.
If you’re sure that the battery pack is in good shape and you purchased a compatible battery from an official dealer, then the issue might just be with the battery.
You need to isolate this issue by looking more at the condition of the charger. If the battery can’t secure a consistent response from the charger, then you can’t expect the battery to work long term.
So, if you didn’t put any mind to finding the right charger or your electrical connections are in poor shape, now is a good time to get a replacement.
You can’t make use of a defective battery or a defective charger, or a defective outlet.
While the situation with the defective battery and the defective charger is easy to fix, you will have to call an electrician to get through the power connections.
There is no point in putting yourself at risk, and the expert will make sure that you never have to worry about a defective connection again.
Just make sure to get your electrical connections checked every six months, and it is smooth sailing after that.
Hopefully, the battery will work perfectly once you address the charger issues and secure the proper power supply to the unit.
- Temperature Issues
Similar to other press tools in the market, you need to pay some attention to the temperature management of the Milwaukee M18 system.
When the temperature is too high or too low, the unit will start flashing red light.
This will show that there is some fault in the connection of the battery pack or that the device is too hot. If that is the issue, then you need to let the device cool down for a few minutes.
While these units are designed to work in extreme conditions, excessive exposure to stress is never a good idea.
You need to focus more on managing the temperature by taking a few breaks. Using this unit for hours on end to get through the project quickly will only damage the tool.
Moreover, you’ll notice poor efficiency, in the long run, eliminating the whole point of getting through the project quickly.
On the other hand, if the unit has been in storage for a while and you live somewhere with extreme cold, the issue might be with the temperature being too low.
You need to focus more on letting the device heat up near a heater. However, you shouldn’t put it too close to the heater and let it warm up slowly.
From there, you can try to reconnect the battery and engage the system. It will start working in a few minutes, and from there, you won’t have to worry about the red flashing light in M18.
- Maintenance Difficulties
One of the biggest things that you need to keep in mind when making the purchase is the maintenance requirements of the tool.
Options like Milwaukee are great when you’re keeping track of their maintenance. However, ignoring the maintenance for a few weeks will result in a lot of issues.
If you’re in the same boat with the Milwaukee system, we suggest that you go through the manual or some online guide to educate yourself on the basic maintenance routine.
It will take a while to get used to the maintenance, and there is no other way around it.
Some people also refer to professionals when they can’t seem to narrow down the problem.
So, if you’re in the same boat as the Milwaukee system, be sure to reach out to an expert.
He will guide you better on how to best take care of the unit. That will also save you a lot of time in the long run.
- Tool not Pressing
The tool not pressing while it is powered on is something that you should also be careful about.
That is why you will need to ensure that you are getting it checked up properly by the Milwaukee support center, the hat should help without having to face any further problems.
These experts will be more than happy to help you inspect the unit for hardware issues. If the device is indeed damaged, you can get a new one by claiming the warranty.
Moreover, if you’re not too sure about the warranty, the new tool will be a bit heavy on your budget.
So, check the purchase date and then forward a warranty claim. As long as the warranty is valid, you won’t have to worry about a thing.
On the other hand, you will have to take the tool to a repair center if it is in poor shape.
Wrapping Up
These are some pointers that you need to keep in mind when purchasing the Milwaukee M18 Propress.
The majority of these issues can be avoided by keeping track of maintenance.
So, if you’re new to the market or can’t seem to find the right routine, be sure to seek help from an expert.
From there, you can secure a consistent response from the press. There are no methods that can help you get through these issues if you keep ignoring the maintenance.
So, go through the manual for a better understanding of the issue.